又爽又黄无遮挡高潮视频网站,久久精品人妻一区二区三区,粗壮挺进人妻水蜜桃成熟漫画,日韩人妻无码精品无码中文字幕

適用於各種金屬、玻璃、陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面、靜電噴漆面及烤漆面等制品的絲印及移印，不需加固化劑，不需烘烤，即可獲得優異的附著力。油墨特性：1、平光(如需亮光請選擇我司jl系列)、附著力佳、耐酒精、耐化學品；2、手感好，流平性佳、面光潔；3、表面硬度好，耐沖擊性能強、抗刮傷；4、耐酒精、耐化學品程度佳；印刷：選用網目為100-420目，以120t聚酯單絲、感光膠網版計算塗覆蓋面積每公斤達35~40㎡。表幹時間自然揮發5-10分鐘，實幹時間在24小時以內，48小時後達優秀性能。1.用b-03專用稀釋劑開油水2.用718洗網水洗網。3.可選擇添加js-9硬化劑10％用於增加油墨附著力及物理化學抗性。4.烤箱80℃烘烤30分鐘佳能更優。測試方法(完全幹燥後)：1.3m膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。2.純度99％的酒精500g力在油墨表面來回擦拭200次無脫色。使用方法：1.使用前應充分攪拌，用後隨時密封。2.攪拌時先加固化劑靜置10分鐘後，再加稀釋劑10-15％，稀釋到印刷粘度。3. 加入固化劑的油墨使用時限為4-6小時，過期請棄用，剩余油墨不可回收。one c o mponent of alumina inkapplicable for all kinds of metal, glass, ceramics, stone, electroplating (aqueous electroplating), anodic alumina surface, electrostatic painting surface【敏感詞】face painting【敏感詞】other products【敏感詞】silk screen printing, without curing agent,【敏感詞】does not need to bake, can obtain excellent adhesion. ink characteristics: 1, plano (for light please choose our jl series), good adhesion, resistance to alcohol, resistant to chemicals; 2, good hand feeling, good leveling, smooth surface; 3, good surface hardness, strong shock resistance, anti scratch; 4, alcohol resistant, chemical resistant degree is good; printing: choice of mesh for 100-420 orders, in 120t polyester monofilament, photosensitive adhesive screen calculation coated area coverage per kilogram of 35-40 square meters. table dry time natural volatile 5-10 minutes, hard work time within 24 hours, 48 hours after the outstanding performance. 1 use b-03 special diluent open oil water 718 with 2 wash n e t. 3 can choose js-9 10％ add hardening agent used to increase the ink adhesion【敏感詞】physical【敏感詞】chemical resistance. 4 oven 80 degrees bake 30 minutes canon better. test method (c o mpletely dry):1.3m gummed paper tape‘s ink surface 45 degree angle quickly pulled off the oil painting. 2 purity of 99％ alcohol 500g force on the surface of the ink back【敏感詞】forth 200 times without decolorization. usage: 1 before use should be fully stirred, sealed at any time after use. 2 stirring, adding the curing agent for 10 minutes, then add the diluent 10-15％, diluted to printing viscosity. 3 add hardener inks use time is 4-6 hours, please not expired, the remaining ink unrecyclable.